65 70 G 10 3892508 1 7 40 40 V z O L x 1V O D 67 70 G 20 3889572 1 7 10 43 O L 67 68 4 WD 3912018 1 26 10 51 0 L Dana 31879 2 69 4 WD 3958030 1 54 05 Dana 35167 1 69 Blazer 3965140 1 33 30 Danai 35167 2 70 Ser 10 20 4 WD Blazer 3979439 1 33 10 Danal 35167 3 6 232 SLEEVE Front Axle Tie Rod 60 64 Ser 10 thru 30 exc D D 4 WD 61 64 Ser 10 D D 3854805 2 1 80 adjusting 8 z 0 D 18 x 1 63 64 Ser 10 w P S exc 4 WD D D 3829582 1 4 35 adjusting P S Installation Unit 65 66 Ser 10 exc D D 4 WD 67 68 Ser 10 thru 30 w P S exc D D 4 WD 68 Ser 20 30 D D w P S 3854807 2 4 90 adj P S Installation Unit 65 67 Ser 10 thru 30 exc D D 4 WD P S 65 69 Ser 10 exc 4 WD 70 Ser 10 thru 30 Conv D D adj 6 0 L l D x Wu O D 68 69 Ser 20 30 exc 4 WD P S 3855946 2 1 75 w intergral pwr strg 6 233 END ASSY UN T Tie Rod NOTE On End Assys requiring a dust seal see Group 6 111 38 All exc EC FC GB HB 38 42 Comm 46 59 V2 V4 Ton exc D D 374227 1 3 35 left 4 z 16 L H thd stmpd L 38 Pass exc EC FC GB HB 38 42 Comm 46 59 V2 V4 Ton exc D D 374226 1 3 35 right 4 Wu 16 R H thd stmpd R 46 55 1 Ton exc UJ UK SBC H D 1st Ser 46 59 1 Ton exc 4 WD 601395 1 7 35 left 4 long 18 L H thd 46 55 1 Ton exc UJ UK VJ VK SBC H D 2 46 59 1 Ton exc 4 WD 601396 1 7 35 right 4 long 18 R H thd 46 59 D D 60 63 D D exc 102 W B 609747 1 10 15 5 long 1 16 L H thd 46 59 D D 60 63 D D exc 102 W B 609748 1 10 15 right use w 3681101 frgd on I beam 5 long 1 16 R H thd 60 62 Ser 10 exc 4 WD 3790672 A R 4 75 short SVI center of socket to end 60 62 Ser 10 exc 4 WD 3769283 2 6 30 long forged 3769284 60 63 Ser 10 4 WD 60 Ser 20 4 WD 2421499 1 3 35 right stud extends W2 from socket 60 63 Ser 10 4 WD 60 Ser 20 4 WD 2421500 1 3 35 left stud extends W1 from socket 60 64 Ser 20 30 exc 4 WD D D 3762351 1 7 35 left inner long 8 center of socket to end 60 64 Ser 20 30 exc 4 WD 0 D 3762352 1 7 35 right inner long 8 center of socket to end 60 64 Ser 20 30 exc 4 WD D D 3767074 1 6 80 left outer short 37m center of socket to end 60 64 Ser 20 30 exc 4 WD D D 3757564 1 6 80 right outer short 3V center of socket to end 61 66 Ser 20 4 WD 64 66 Ser 10 4 WD 2476922 1 3 16 R H thd Note 1 61 66 Ser 20 4 WD 64 66 Ser 10 4 WD 2476923 1 10 00 3 16 L H thd Note 1 NOTE 1 Both L H R H tie rod ends T G with tie rod must be replaced when sub is made on either tie rod end 63 64 Ser 10 exc 4 WD 3817953 2 6 30 long 6 z O L forged 3817954 63 64 Ser 10 exc 4 WD 64 G 10 3826596 2 4 70 left J3 0 L forged 3826597 64 G 10 3826814 2 4 70 R H thread 3 O L forged 3826815 64 67 D D exc 102 W B 64 67 D D exc 102 W B 65 67 Ser 20 exc 4 WD D D 68 69 Ser 20 30 exc 4 WD 70 Ser 20 30 Conv D D 3908295 1 7 45 L H thread 65 68 Ser 20 30 exc 4 WD D D 68 69 Ser 20 30 exc 4 WD 70 Ser 20 30 Conv D D 3908296 1 7 45 R H thread 1971 CHEVROLET MOTOR DIVISION GEENERAL IVIOTORS CORPORATION P A 31T REV 6 71 6 13 6 230 6 233